Visit The Following Page

 

This great article which follows relating to How to Install a Bathtub is relatively enlightening. You should investigate for yourself.

Mounting a bath tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably tough project. If the old tub is easily easily accessible, the task can relocate quickly; if you need to open up a wall to eliminate the old tub and also position the new bath tub, the task is much harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and also set in the brand-new one. Make sure you have qualified on your own for the work as well as fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is far better to take into consideration using one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your washroom if you have already gotten a brand-new bathtub and don't need to alter the setup of your previous water supply pipes.
Your tools and material checklist should comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you need to replace old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain any kind of water staying in the system. The process of removing the existing taps can be fairly problematic as a result of the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will originate from the pipelines. When the supply pipelines have been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The former kind should be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Setting up the Bathtub

Using both wooden boards under its feet, position the tub in the needed placement. The wood boards are handy in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the tub up until the level checks out degree.
To set up taps, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the water system and also inspect all joints and also new pipework for leakages and also tighten them if required. Load the tub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub ought to wait up until the tub has actually been used at the very least once as this will certainly resolve it into its last setting.

 

 

Getting ready for the Installation

First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a stiff seal, creating the water to pass through the wall surface in between the bath and also the tiling, bring about issues with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the tub with water before securing, to allow for the activity experienced when the tub is in use. The sealant can split fairly early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We had been shown that article on A Step-by-Step Guide to Installing a Bathtub from a good friend on another blog. Sharing is caring. Helping people is fun. We treasure reading our article about How to Install a Bathtub Yourself.

Avoid further plumbing damage; call.